4-HOUR SINGLE DOOR HAZARDOUS MATERIAL STORAGE BUILDING
Each 4-hour single door hazardous chemical storage building has the following features:
- AH 4-hour rated UL DES U419 walls & ceilings Class 1, Div 2 Compliant
- Drum Capacity: 27
- Sump Capacity: 545.33 gallons
- Wind Force Rating: 150mph
- Single set end doors (gives you more storage space)
- 20′ long x 8′ wide x 8.5′ tall ISO container
- 14 gauge corrugated steel
- Pryo Chem Monarch PCI-35ABC Dry Chemical Fire Suppression System meets or exceeds NFPA Code 17, 17A, and 30 Specifications
- Canarm Explosion-Proof Enclosed Exhaust Fan – 12in giving 1,640 CFM (More than two times that of industry standards)
- Built-in Security 6″ deep steel floor sump for spill containment
- Flip-up Steel non-skid Floor Grating Provides Full Access to Secondary Containment
- Interior Explosion Proof Lighting
- Static Grounding system
- Drum Capacity: 27
- 4 top and bottom 4 bottom crane pad eyes
- Forklift pockets
- Premium, high-solids formula with acrylic polymers, resins, fillers, and titanium dioxide pigments white outside paint coating that Reflects 92% of solar heat and rays for a cooler inside temp.
- 220V, Single-Phase 50-amp Electrical requirement. We will provide a female SOOW (Service Cord) plug to connect directly into the unit’s power panel. The unit must also be properly grounded by connecting a green ground wire coming out of the power panel to an 8’ copper grounding rod which must be driven down 95 percent in the ground. Each unit will be provided one grounding rod.
- All vent openings are equipped with three-hour, UL Listed fire dampers and foul weather hoods.
Our 4-hour single door hazardous material storage building models are designed with the active job site in mind. Combined with the optional shelving, this container is perfect for storing your product contained within smaller handheld containers. Opening the 2 large doors that are situated at the front of the container will give you unobstructed access to the inside, making it easier to move your product in and out when your hands are full. The overall design of the single door chemical storage shipping containers maximizes the usable space on the inside and outside of the unit. The single door design is best if your project’s lay-down space is limited. These units can be stacked side by side, allowing you to fit more containers in a small area. Add the optional air conditioner and heater to control the temperature of your products.
We won’t leave you in the dark
This single door hazardous waste storage building model can be configured in 9 different ways, depending on the container size and bidirectional fire ratings. Available in
- Drum Capacity: 9 (single stacked).
- Pallet capacity 48” x 40”: 4.
- Sump Capacity: 307 gallons Fully welded and liquid tight.
- Wind Force Rating: 150mph.
- Exterior dimensions: 10′ long x 8′ wide x 8’6″ tall ISO container. The electrical power panel and FSS alarm bell protrude an additional 6-½” giving a total length of 126.½”. The optional air conditioner unit if installed protrudes 21″ off the container’s back wall giving a total length of 141″.
- GVW: 4,500 pounds
- Liquid gallon capacity: 1,023.33 gallons.
- Canarm non-sparking Explosion-Proof Enclosed Exhaust Fan – 12 gives 1,640 CFM which exceeds NFPA 30.18.6.6.1 & NFPA 30.18.6.2.
- Floor grading support beams at 2 ft on Center.
- Removable Steel non-skid Floor Grating Provides Full Access to Secondary Containment.
- Interior Explosion Proof Lighting Class 1, Division 2
- All applicable placards and stickers that include: No Smoking within 50 feet, NFPA diamond, NPPA Aluminum Flip File Placard, 10-Legend Worded Set, intended use Warning sticker, Warning Over Hang sticker.
- 4 top and bottom 4 bottom crane pad eyes
- Forklift pockets: 51″ outside to outside of the forklift pockets / 23″ inside to inside of the forklift pockets / 37¼” center of the forklift pocket to center of the forklift pocket / Each forklift pocket is 14″ wide 4¼” tall.
- Premium, high-solids formula with acrylic polymers, resins, fillers, and titanium dioxide pigments white outside paint coating that Reflects 92% of solar heat and rays for a cooler inside temp.
- Built to comply with NFPA Code 17, 17A, 30, and 70 Specifications. Approved holding of hazardous and flammable materials in accordance with local regulations.
- Pallet capacity 48” x 40”: 4.
- Wind Force Rating: 150mph.
- 4 top and bottom 4 bottom crane pad eyes
- End door opening 7’6″ wide x 7′ tall.
- Interior dimensions: 9′ deep (92″ to the exhaust fan) x 92 wide x 88″ tall (76″ Floor to bottom of the light).
- GVWR: 29,910 pounds
- 14-gauge Corten corrugated steel construction.
- Pryo Chem Monarch PCI-35ABC Dry Chemical Total Flooding Fire Suppression System. Equipped with an external remote pull station, external audible alarm, and control head micro switch which cut power to the exhaust fan when the system has been activated. Design to meet or exceeds NFPA Code 17-(Standard for Dry Chemical Extinguishing Systems), and NFPA 30-(Flammable and Combustible Liquids Code) Specifications.
- Built-in secondary Security 6in deep steel floor sump for spill containment
- Galvanized grading is rated at 632 pounds per square foot.
- 2 door vents equipped with foul weather hoods.
- Static Grounding system.
- 220V, Single-Phase 50-amp Electrical requirement. Each container will have a Marine Shore Power Inlet, model number RV129R, 50A 125/250Vac male electrical plug pre-installed near the unit’s power panel. We will provide a female Marine Shore Power Inlet, model number ED-RV129, 50A 125/250Vac plug that will need to be connected to a 4-wire SOOW cable. This cable must be provided by the customer. The unit must also be properly grounded by connecting a green ground wire coming out of the power panel to an 8’ copper grounding rod which must be driven down 95% in the ground. Each unit will be provided with one grounding rod and clamp.
- AH 2-hour rated UL DES U419 / MEA 81-98-M walls & ceilings Class 1, Division 2 Compliant.
- Drum Capacity: 9.
- Pallet capacity 48″ x 40″: 4.
- Sump Capacity: 280 gallons.
- Wind Force Rating: 150mph.
- Exterior dimensions: 10ft long x 8ft wide x 8½ft tall ISO container. The electrical power panel and FSS alarm bell protrude an additional 6-½” giving a total length of 126.½”. The optional air conditioner unit if installed protrudes 21″ off the container’s back wall giving a total length of 141″.
- Interior dimensions: 102″ deep (87-½” deep to the fan) x 81″ wide x 83-½” tall. (71-½” Floor to bottom of the light / 78″ Floor to bottom of the FSS nozzles).
- Double door opening: 80″ wide x 84″ tall.
- GVW: 7,600 pounds.
- GVWR: 29,910 pounds.
- Liquid gallon capacity: 933.33 gal.
- Lockable and Weatherproof Construction.
- 14-gauge corrugated steel.
- Pryo Chem Monarch PCI-35ABC Dry Chemical Total Flooding Fire Suppression System. Equipped with an external remote pull station, external audible alarm, and control head micro switch which cut power to the exhaust fan when the system has been activated. Design to meet or exceeds NFPA Code 17-(Standard for Dry Chemical Extinguishing Systems), and NFPA 30- (Flammable and Combustible Liquids Code) Specifications.
- Canarm non-sparking Explosion-Proof Enclosed Exhaust Fan – 12 gives 1,640 CFM which exceeds NFPA 30.18.6.6.1 & NFPA 30.18.6.2.
- Built-in secondary Security 6in deep steel floor sump for spill containment
- Floor grading support beams at ft on Center.
- Galvanized grading is rated at 632 pounds per square foot.
- Removable Steel non-skid Floor Grating Provides Full Access to Secondary Containment.
- Interior Explosion Proof Lighting Class 1, Division 2.
- All applicable placards and stickers that include: No Smoking within 50 feet, NFPA diamond, NPPA Aluminum Flip File Placard, 10-Legend Worded Set, intended use Warning sticker, Warning Over Hang sticker.
- 4 top and bottom 4 bottom crane pad eyes.
- Forklift pockets: 51″ outside to outside of the forklift pockets / 23″ inside to inside of the forklift pockets / 37¼” center of the forklift pocket to center of the forklift pocket / Each forklift pocket is 14″ wide 4¼” tall.
- Premium, high-solids formula with acrylic polymers, resins, fillers, and titanium dioxide pigments white outside paint coating that Reflects 92% of solar heat and rays for a cooler inside temp.
- Vent openings are equipped with two-hour, UL Listed fire dampers, and foul weather hoods.
- Static Grounding system.
- 220V, Single-Phase 50-amp Electrical requirement. Each container will have a Marine Shore Power Inlet, model number RV129R, 50A 125/250Vac male electrical plug pre-installed near the unit’s power panel. We will provide a female Marine Shore Power Inlet, model number ED-RV129, 50A 125/250Vac plug that will need to be connected to a 4-wire SOOW cable. This cable must be provided by the customer. The unit must also be properly grounded by connecting a green ground wire coming out of the power panel to an 8′ copper grounding rod which must be driven down 95% in the ground. Each unit will be provided with one grounding rod and clamp.
- Built to comply with NFPA Code 17, 17A, 30, and 70 Specifications. Approved holding of hazardous and flammable materials in accordance with local regulations.
- AH 4-hour rated UL DES U419 / MEA 81-98-M walls & ceilings Class 1, Division 2 Compliant.
- Drum Capacity: 9.
- Pallet capacity 48″ x 40″: 4.
- Sump Capacity: 280 gallons.
- Wind Force Rating: 150mph.
- Exterior dimensions: 10ft long x 8ft wide x 8½ft tall ISO container. The electrical power panel and FSS alarm bell protrude an additional 6-½” giving a total length of 126.½”. The optional air conditioner unit if installed protrudes 21″ off the container’s back wall giving a total length of 141″.
- Interior dimensions: 101″ deep (86-½” deep to the fan) x 80″ wide x 83-½” tall. (71-½” Floor to bottom of the light / 78″ Floor to bottom of the FSS nozzles).
- Double door opening: 80″ wide x 84″ tall.
- GVW: 8,400 pounds.
- GVWR: 29,910 pounds.
- Liquid gallon capacity: 933.33 gallons.
- Lockable and Weatherproof Construction.
- 14-gauge corrugated steel.
- Pryo Chem Monarch PCI-35ABC Dry Chemical Total Flooding Fire Suppression System. Equipped with an external remote pull station, external audible alarm, and control head micro switch which cut power to the exhaust fan when the system has been activated. Design to meet or exceeds NFPA Code 17-(Standard for Dry Chemical Extinguishing Systems), and NFPA 30-(Flammable and Combustible Liquids Code) Specifications.
- Canarm non-sparking Explosion-Proof Enclosed Exhaust Fan – 12 gives 1,640 CFM which exceeds NFPA 30.18.6.6.1 & NFPA 30.18.6.2.
- Built-in secondary Security 6in deep steel floor sump for spill containment.
- Floor grading support beams at 2 ft on Center.
- Galvanized grading is rated at 632 pounds per square foot.
- Removable Steel non-skid Floor Grating Provides Full Access to Secondary Containment.
- Interior Explosion Proof Lighting Class 1, Division 2.
- All applicable placards and stickers that include: No Smoking within 50 feet, NFPA diamond, NPPA Aluminum Flip File Placard, 10-Legend Worded Set, intended use Warning sticker, Warning Over Hang sticker.
- 4 top and bottom 4 bottom crane pad eyes.
- Forklift pockets: 51″ outside to outside of the forklift pockets / 23″ inside to inside of the forklift pockets / 37¼” center of the forklift pocket to center of the forklift pocket / Each forklift pocket is 14″ wide 4¼” tall.
- Premium, high-solids formula with acrylic polymers, resins, fillers, and titanium dioxide pigments white outside paint coating that Reflects 92% of solar heat and rays for a cooler inside temp.
- Vent openings are equipped with three-hour, UL Listed fire dampers, and foul weather hoods.
- Static Grounding system.
- 220V, Single-Phase 50-amp Electrical requirement. Each container will have a Marine Shore Power Inlet, model number RV129R, 50A 125/250Vac male electrical plug pre-installed near the unit’s power panel. We will provide a female Marine Shore Power Inlet, model number ED-RV129, 50A 125/250Vac plug that will need to be connected to a 4-wire SOOW cable. This cable must be provided by the customer. The unit must also be properly grounded by connecting a green ground wire coming out of the power panel to an 8′ copper grounding rod which must be driven down 95% in the ground. Each unit will be provided with one grounding rod and clamp.
- Built to comply with NFPA Code 17, 17A, 30, and 70 Specifications. Approved holding of hazardous and flammable materials in accordance with local regulations.
- Drum Capacity: 27 (single stacked).
- Pallet capacity 48″ x 40″: 10.
- Sump Capacity: 545-625 gallons Fully welded and liquid tight.
- Wind Force Rating: 150mph.
- End door opening: 90″ wide x 84″ tall.
- Exterior dimensions: 20′ long x 8′ wide x 8’6″ tall ISO container. The electrical power panel and FSS alarm bell protrude an additional 6-½” giving a total length of 246-½”. The optional air conditioner unit if installed protrudes 20″ off the container’s back wall giving a total length of 260″.
- Interior dimensions: 235″ deep (220-½” to the exhaust fan) x 92″ wide x 88″ tall (76″ Floor to bottom of the light).
- GVW: 6,580 pounds.
- GVWR: 62,500 pounds.
- Lockable and Weatherproof Construction.
- 14-gauge Corten corrugated steel construction.
- Liquid gallon capacity: 1,833-2,083 gallons.
- Pryo Chem Monarch PCI-35ABC Dry Chemical Total Flooding Fire Suppression System. Equipped with an external remote pull station, external audible alarm, and control head micro switch which cut power to the exhaust fan when the system has been activated. Design to meet or exceeds NFPA Code 17-(Standard for Dry Chemical Extinguishing Systems), and NFPA 30-(Flammable and Combustible Liquids Code) Specifications.
- Canarm non-sparking Explosion-Proof Enclosed Exhaust Fan – 12in giving 1,640 CFM which exceeds NFPA 30.18.6.6.1 & NFPA 30.18.6.2.
- Built-in secondary Security 6in deep steel floor sump for spill containment.
- Floor grading support beams at 2 ft on Center.
- Galvanized grading is rated at 632 pounds per square foot.
- Removable Steel non-skid Floor Grating Provides Full Access to Secondary Containment.
- Interior Explosion Proof class 1 division 2 Lighting.
- 2 door vents equipped with foul weather hoods.
- All applicable placards and stickers that include: No Smoking within 50 feet, NFPA diamond, NPPA Aluminum Flip File Placard, 10-Legend Worded Set, intended use Warning sticker, Warning Over Hang sticker.
- 4 top and 4 bottom crane padeyes.
- Forklift pockets: 96″ outside to outside of the forklift pockets / 67¾” inside to inside of the forklift pockets / 81½” center of the forklift pocket to center of the forklift pocket / Each forklift pocket is 14″ wide 4¼” tall.
- Premium, high-solids formula with acrylic polymers, resins, fillers, and titanium dioxide pigments white outside paint coating that Reflects 92% of solar heat and rays for a cooler inside temp.
- Static Grounding system.
- 220V, Single-Phase 50-amp Electrical requirement. Each container will have a Marine Shore Power Inlet, model number RV129R, 50A 125/250Vac male electrical plug pre-installed near the unit’s power panel. We will provide a female Marine Shore Power Inlet, model number ED-RV129, 50A 125/250Vac plug that will need to be connected to a 4-wire SOOW cable. This cable must be provided by the customer. The unit must also be properly grounded by connecting a green ground wire coming out of the power panel to an 8′ copper grounding rod which must be driven down 95% in the ground. Each unit will be provided with one grounding rod and clamp.
- Built to comply with NFPA Code 17, 17A, 30, and 70 Specifications. Approved holding of hazardous and flammable materials in accordance with local regulations.
- AH 2-hour rated UL DES U419 / MEA 81-98-M walls & ceilings Class 1, Division 2 Compliant.
- Drum Capacity: 27.
- Pallet capacity 48″ x 40″: 8.
- Sump Capacity: 545.33 gallons Fully welded and liquid tight.
- Wind Force Rating: 150mph.
- End door opening: 80″ wide x 83″ tall.
- Exterior dimensions: 20′ long x 8′ wide x 8.½’ tall ISO container. The electrical power panel and FSS alarm bell protrude an additional 6-½” giving a total length of 246-½”. The optional air conditioner unit if installed protrudes 17″ off the container’s back wall giving a total length of 257″.
- Interior dimensions: 221″ deep (206-½” deep to the fan) x 82.½” wide x 84′ tall (72″ Floor to bottom of the light / 78.½” Floor to bottom of the FSS nozzles).
- GVW: 13,000 pounds.
- GVWR: 66,139 pounds.
- Liquid gallon capacity: 1,817.76 gallons.
- Lockable and Weatherproof Construction.
- 14-gauge corrugated steel.
- Pryo Chem Monarch PCI-35ABC Dry Chemical Total Flooding Fire Suppression System. Equipped with an external remote pull station, external audible alarm, and control head micro switch which cut power to the exhaust fan when the system has been activated. Design to meet or exceeds NFPA Code 17-(Standard for Dry Chemical Extinguishing Systems), and NFPA 30- (Flammable and Combustible Liquids Code) Specifications.
- Canarm non-sparking Explosion-Proof Enclosed Exhaust Fan – 12in giving 1,640 CFM which exceeds NFPA 30.18.6.6.1 & NFPA 30.18.6.2.
- Built-in secondary Security 6in deep steel floor sump for spill containment.
- Floor grading support beams at 2 ft on Center.
- Galvanized grading is rated at 632 pounds per square foot.
- Removable Steel non-skid Floor Grating Provides Full Access to Secondary Containment.
- Interior Explosion Proof Lighting Class 1, Division 2.
- All applicable placards and stickers that include: No Smoking within 50 feet, NFPA diamond, NPPA Aluminum Flip File Placard, 10-Legend Worded Set, intended use Warning sticker, Warning Over Hang sticker.
- 4 top and bottom 4 bottom crane pad eyes.
- Forklift pockets: 96″ outside to outside of the forklift pockets / 67¾” inside to inside of the forklift pockets / 81½” center of the forklift pocket to center of the forklift pocket / Each forklift pocket is 14″ wide 4¼” tall.
- Premium, high-solids formula with acrylic polymers, resins, fillers, and titanium dioxide pigments white outside paint coating that Reflects 92% of solar heat and rays for a cooler inside temp.
- Vent openings are equipped with three-hour, UL Listed fire dampers, and foul weather hoods.
- Static Grounding system.
- 220V, Single-Phase 50-amp Electrical requirement. Each container will have a Marine Shore Power Inlet, model number RV129R, 50A 125/250Vac male electrical plug pre-installed near the unit’s power panel. We will provide a female Marine Shore Power Inlet, model number ED-RV129, 50A 125/250Vac plug that will need to be connected to a 4-wire SOOW cable. This cable must be provided by the customer. The unit must also be properly grounded by connecting a green ground wire coming out of the power panel to an 8′ copper grounding rod which must be driven down 95% in the ground. Each unit will be provided with one grounding rod and clamp.
- Built to comply with NFPA Code 17, 17A, 30, and 70 Specifications. Approved holding of hazardous and flammable materials in accordance with local regulations.
- AH 4-hour rated UL DES U419 / MEA 81-98-M walls & ceilings Class 1, Division 2 Compliant.
- Drum Capacity: 27.
- Pallet capacity 48″ x 40″: 8.
- Sump Capacity: 545.33 gallons Fully welded and liquid tight.
- Wind Force Rating: 150mph.
- End door opening: 80″ wide x 83″ tall.
- Exterior dimensions: 20′ long x 8′ wide x 8’6″ tall ISO container. The electrical power panel and FSS alarm bell protrude an additional 6-½” giving a total length of 246-½”. The optional air conditioner unit if installed protrudes 15″ off the container’s back wall giving a total length of 255″.
- Interior dimensions: 222½” deep (208″ deep to the fan) x 80.½” wide x 84′ tall (72″ Floor to bottom of the light / 78.½” Floor to bottom of the FSS nozzles).
- GVW: 14,000 pounds.
- GVWR: 66,139 pounds.
- Liquid gallon capacity: 1,817.76 gallons.
- Lockable and Weatherproof Construction.
- 14-gauge corrugated steel.
- Pryo Chem Monarch PCI-35ABC Dry Chemical Total Flooding Fire Suppression System. Equipped with an external remote pull station, external audible alarm, and control head micro switch which cut power to the exhaust fan when the system has been activated. Design to meet or exceeds NFPA Code 17-(Standard for Dry Chemical Extinguishing Systems), and NFPA 30- (Flammable and Combustible Liquids Code) Specifications.
- Canarm non-sparking Explosion-Proof Enclosed Exhaust Fan – 12in giving 1,640 CFM which exceeds NFPA 30.18.6.6.1 & NFPA 30.18.6.2.
- Built-in secondary Security 6in deep steel floor sump for spill containment
- Floor grading support beams at 2 ft on Center.
- Galvanized grading is rated at 632 pounds per square foot.
- Removable Steel non-skid Floor Grating Provides Full Access to Secondary Containment.
- Interior Explosion Proof Lighting Class 1, Division 2.
- All applicable placards and stickers that include: No Smoking within 50 feet, NFPA diamond, NPPA Aluminum Flip File Placard, 10-Legend Worded Set, intended use Warning sticker, Warning Over Hang sticker.
- 4 top and bottom 4 bottom crane pad eyes.
- Forklift pockets: 96″ outside to outside of the forklift pockets / 67¾” inside to inside of the forklift pockets / 81½” center of the forklift pocket to center of the forklift pocket / Each forklift pocket is 14″ wide 4¼” tall.
- Premium, high-solids formula with acrylic polymers, resins, fillers, and titanium dioxide pigments white outside paint coating that Reflects 92% of solar heat and rays for a cooler inside temp.
- Vent openings are equipped with three-hour, UL Listed fire dampers, and foul weather hoods.
- Static Grounding system.
- 220V, Single-Phase 50-amp Electrical requirement. Each container will have a Marine Shore Power Inlet, model number RV129R, 50A 125/250Vac male electrical plug pre-installed near the unit’s power panel. We will provide a female Marine Shore Power Inlet, model number ED-RV129, 50A 125/250Vac plug that will need to be connected to a 4-wire SOOW cable. This cable must be provided by the customer. The unit must also be properly grounded by connecting a green ground wire coming out of the power panel to an 8′ copper grounding rod which must be driven down 95% in the ground. Each unit will be provided with one grounding rod and clamp.
- Built to comply with NFPA Code 17, 17A, 30, and 70 Specifications. Approved holding of hazardous and flammable materials in accordance with local regulations.